Acceptance Mark

Official PayPal Seal



(Your shopping cart is empty)
You are here: Home > Mustang > 2005-2009 Mustang > 5.4L Shelby GT500 > Engine
Sort By
Page of 2
ROLLER PILOT BEARING 4.6L/5.4L AND 5.0L 4V TIVCT MODULAR ENGINES -- M-7600-B FORD RACING HIGH-PERFORMANCE OIL FILTER (single filter)
Our Price:$12.95
Our Price:$16.95

(4)
ROLLER PILOT BEARING 4.6L/5.4L AND 5.0L 4V TIVCT MODULAR ENGINES -- M-7600-B FORD RACING HIGH-PERFORMANCE OIL FILTER
  • Production roller pilot bearing fits 4.6L/5.4L and 5.0L 4V TI-VCT modular engines

NOTE: Pre-greased do not add extra grease. Clutch and bearing damage may occur

  • Upgraded Direct Replacement for Motorcraft FL-820S oil filter.
    So any application that uses a Motorcraft FL-820S oil filter can benefit
    from using this upgraded oil filter.
  • Synthetic-Polymer/Cellulose-Fiber blend media
  • Heavy-gauge base and canister for higher burst strength and impulse fatigue resistance
  • High-quality silicone anti-drain back valve
  • Non-stick sealing gasket for ease of installation and removal
  • Long life with standard and synthetic motor oils
  • Up to 50% more filtering capacity than standard filters
  • Improved filtering efficiency
  • This technology is only available through Ford Racing Performance Parts
  • Click Here for a Complete Vehicle Application Fitment List
FORD RACING FENDER COVER -- M-1822-A2 2007-2014 Shelby GT500 Powered By SVT Coil Covers -- M-6067-C
Our Price:$16.95

(3)
List Price:$108.95
Our Price:$79.00
You save $29.95!
FORD RACING FENDER COVER -- M-1822-A2 2007-2014 Shelby GT500 Powered By SVT Coil Covers -- M-6067-C
Protect that beautiful paint job from scratches, chemicals and oil with this strong, sturdy and slip-resistant "Ford Racing" fender cover.  Measures 27'' x 36'' and is acid and grease resistant. Features handy "ridged" area in which to place small tools and parts.

2007-2014 Shelby GT500 Powered By SVT Coil Covers

M-6067-C

  • Original equipment on the 2007-2014 Shelby GT500
  • Fits most 4.6L/5.4L/5.8L DOHC engines with coil on plug ignition
2005-2014 MUSTANG HOOD LIFT KIT W/ LASER ENGRAVED FORD PERFORMANCE LOGO -- M-16826-M 4.6L/5.4L/5.8L HIGH VOLUME OIL PUMP W/ PICK UP -- M-6600-F46
List Price:$99.00
Our Price:$82.00
Sold as a Set
You save $17.00!
Our Price:$135.00
2005-2014 MUSTANG HOOD LIFT KIT W/ LASER ENGRAVED FORD PERFORMANCE LOGO -- M-16826-M 4.6L/5.4L/5.8L HIGH VOLUME OIL PUMP W/ PICK UP -- M-6600-F46
  • Fits 2005-2014 Mustangs Ford Performance Hood Lift Kit w/ Laser Engraved Ford Performance Logo.
  • 90 LBS Rating
  • Designed for all OEM base, Mustang GT, GT500, GT350, and many aftermarket hoods
  • These hood lifts utilize two gas struts that lift and hold the hood without the need for a prop-rod.
  • Made from lightweight steel and aluminum, they feature a durable black power coated finish to give your engine bay a much cleaner appearance.
  • Includes the necessary mounting brackets
  • No Drilling Required. The stamped steel brackets included in this kit are designed to bolt into the existing mounting holes in the hood so there is no drilling required for installation
  • If your aftermarket hood is lighter than the factory hood, use caution when opening the hood due to the power of the strut.
  • Fits: 2005-2010 4.6L 3V Mustang 2007-2012 5.4L 4V Shelby GT500, 2013-2014 5.8L 4V Shelby GT500
  • Stock replacement for 2013-2014 5.8L 4V Shelby GT500
  • Pump has a thick steel backing plate to reduce pump housing flex which can lead to aeration in high performance use in modified engines or higher than factory RPM
  • Includes a steel backing plate that:
    • reduces internal leakage
    • reduces cavitation erosion
  • Includes pick-up tube
2007-2014 MUSTANG SHELBY GT500 THROTTLE BODY -- M-9926-MSVT 5.4L STEEL TIMING CHAIN TENSIONER KIT -- M-6266-54ST
Our Price:$149.95
List Price:$175.00
Our Price:$155.00
You save $20.00!
2007-2014 MUSTANG SHELBY GT500 THROTTLE BODY -- M-9926-MSVT 5.4L STEEL TIMING CHAIN TENSIONER KIT -- M-6266-54ST
  • Fits 2007-2014 Mustang Shelby GT500
  • New stock replacement 60mm throttle body
  • Fits 4-valve 5.4L engines
  • Production steel primary and secondary timing chain tensioners
  • Includes PN F6AZ-6L266-DA and F6AZ-6L266-CA (1 of each PN)
  • 2 kits required per engine

2007-2012 SHELBY GT500 Stock Supercharger 2.6 Inch Pulley (Adds 4-5 lbs of boost) -- GT 110261 2007-2012 SHELBY GT500 TVS Supercharger 2.6 Inch Pulley (Adds 4-5 lbs of boost) -- GT 210261
Our Price:$159.67
Our Price:$159.67

(1)
2007-2012 SHELBY GT500 Stock Supercharger 2.6 Inch Pulley (Adds 4-5 lbs of boost) -- GT 110261 2007-2012 SHELBY GT500 TVS Supercharger 2.6 Inch Pulley (Adds 4-5 lbs of boost) -- GT 210261
These pieces are the highest quality supercharger pulleys for your Shelby GT500. This pulley is a 10-rib 2.6 inch diameter drive pulley for the stock Shelby GT500 Supercharger. It is meant to have a stock look while allowing you to gain performance with an additional 4 psi of boost on the stock supercharger.

AFTERMARKET COMPUTER CALIBRATION REQUIRED
As with any supercharger pulley upgrade, an aftermarket computer calibration is required and is not included. The Ford Racing ProCal tuner does not support this supercharger pulley change.

MUST USE GT 9000 IDLER TENSIONER ARM ASSEMBLY
The OEM tensioner arm does not have enough range of motion to ensure proper belt tension. Failure to purchase and install our tensioner arm assembly when using a smaller than stock supercharger pulley will result in belt slippage under acceleration.

Why these pulleys are better

  • Each pulley consists of precision machined grooves to ensure proper fitment with the belt. Inferior designed grooves will rip belts apart. The pulley to belt contact area is a critical design element and the pulley design is the result of many revisions to virtually eliminate slippage.
  • To eliminate the issue of the pulley slipping on the supercharger shaft, these pulleys are honed bore, round & straight within .0002.
  • Proper Lead-in is designed into each pulley to ensure that the it goes on straight.
  • Made In the USA
These pieces are the highest quality supercharger pulleys for your Shelby GT500. This pulley is a 10-rib 2.6 inch diameter drive pulley for the aftermarket TVS Supercharger. It is meant to have a stock look while allowing you to gain performance with an additional 4 psi of boost on the TVS supercharger.

AFTERMARKET COMPUTER CALIBRATION REQUIRED
As with any supercharger pulley upgrade, an aftermarket computer calibration is required and is not included. The Ford Racing ProCal tuner does not support this supercharger pulley change.

MUST USE GT 9000 IDLER TENSIONER ARM ASSEMBLY
The OEM tensioner arm does not have enough range of motion to ensure proper belt tension. Failure to purchase and install our tensioner arm assembly when using a smaller than stock supercharger pulley will result in belt slippage under acceleration.

Why these pulleys are better

  • Each pulley consists of precision machined grooves to ensure proper fitment with the belt. Inferior designed grooves will rip belts apart. The pulley to belt contact area is a critical design element and the pulley design is the result of many revisions to virtually eliminate slippage.
  • To eliminate the issue of the pulley slipping on the supercharger shaft, these pulleys are honed bore, round & straight within .0002.
  • Proper Lead-in is designed into each pulley to ensure that the it goes on straight.
  • Made In the USA
FORD RACING SVT 5.4L SUPERCHARGED HEAD CHANGING KIT -- M-6067-MSVT FORD RACING HIGH-PERFORMANCE OIL FILTER (case of 12) -- M-6731-FL820
Our Price:$159.95
Our Price:$179.00
Sold in a case of 12
FORD RACING SVT 5.4L SUPERCHARGED HEAD CHANGING KIT -- M-6067-MSVT FORD RACING HIGH-PERFORMANCE OIL FILTER (case of 12) -- M-6731-FL820
  • Fits 5.4L DOHC engines
  • Original equipment on 2007-2011 Mustang SVT and 2008 Mustang FR500CJ race car
  • Improved sealing for high cylinder pressure applications
  • Kit includes multi-layer steel head gaskets and high-strength torque to yield head bolts
  • Upgraded Direct Replacement for Motorcraft FL-820S oil filter.
    So any application that uses a Motorcraft FL-820S oil filter can benefit
    from using this upgraded oil filter.
  • Synthetic-Polymer/Cellulose-Fiber blend media
  • Heavy-gauge base and canister for higher burst strength and impulse fatigue resistance
  • High-quality silicone anti-drain back valve
  • Non-stick sealing gasket for ease of installation and removal
  • Long life with standard and synthetic motor oils
  • Up to 50% more filtering capacity than standard filters
  • Improved filtering efficiency
  • This technology is only available through Ford Racing Performance Parts
  • Click Here for a Complete Vehicle Application Fitment List
SHELBY GT500 UPGRADED 90MM ADJUSTABLE IDLER ARM ASSEMBLY -- GT 9000 4.6L/5.4L "FORD RACING" CAST COIL COVERS -- M-6067-D
Our Price:$249.97
Our Price:$269.99

(2)
SHELBY GT500 UPGRADED 90MM ADJUSTABLE IDLER ARM ASSEMBLY -- GT 9000 4.6L/5.4L "FORD RACING" CAST COIL COVERS -- M-6067-D
  • Components are CNC machined out of high quality aluminum.
  • High quality Type III hard coat anodized finish.
  • True double-bearing setup can withstand anything you throw at it!
  • Will work with ALL available superchargers, including the Kenne Bell!
  • Designed to work with most common supercharger pulleys.
  • Simple installation without modification!
  • Fits most 4.6L/5.4L DOHC engines with coil on plug ignition
  • Polished die-cast aluminum
  • Features two-color Ford Racing logo
FORD GT 5.4L LASH ADJUSTER SET -- M-6500-GT 2008-2012 Shelby GT500 Upgraded Crank Damper -- M-6312-SVT
Our Price:$279.00
Our Price:$299.00

(2)
FORD GT 5.4L LASH ADJUSTER SET -- M-6500-GT 2008-2012 Shelby GT500 Upgraded Crank Damper -- M-6312-SVT
  • Unique lash adjusters fit Ford GT and Mustang GT500 5.4L/5.8L DOHC cylinder heads  
  • Includes 16 intake and 16 exhaust lash adjusters  
  • New factory replacement damper from the 2008-2012 Shelby GT500 5.4L 4V engine
  • 10 lbs lighter than the 2007 factory Shelby GT500 Crankshaft Damper
  • Must be installed on the 2007 Shelby GT500 Mustang when using the M-6066-SGT on 2007 Shelby GT500 to qualify for warranty.
  • Highly recommended for any 2007 Shelby GT500 when upgrading the supercharger.
FORD RACING SVT 4.6L/5.4L MODULAR UPGRADED ROCKER ARM SET -- M-6529-MSVT POWERMASTER XS TORQUE HIGH TORQUE MINI STARTER 4.6L/5.4/COYOTE 5.0L -- 9532
Our Price:$299.00
Sold in Sets of 16
List Price:$368.75
Our Price:$299.99
You save $68.76!
FORD RACING SVT 4.6L/5.4L MODULAR UPGRADED ROCKER ARM SET -- M-6529-MSVT POWERMASTER XS TORQUE HIGH TORQUE MINI STARTER 4.6L/5.4/COYOTE 5.0L -- 9532
  • Original equipment on Ford GT 5.4L engine
  • Fits 4.6L and 5.4L 4V DOHC SVT engines
  • 4 grams lighter, stiffer, and better engagement on lash adjuster over 4.6L DOHC rocker arms
  • Fits 4.6L/5.4L/Coyote 5.0L
  • 4.4:1 Gear Reduction
  • 200 ft-lb rating
  • Small diameter mini-starter great for additional header and oil pan clearance
  • No heat soak problems
  • Weighs 8.5 lbs.  The lightest 200 ft-lb starter available.
  • Machined Billet Aluminum Adapter Block
  • Every starter is individually tested and dyno results sheet is included in the box
  • Starter bolts are not included.  Starter bolts can be sourced from your local Ford Dealer.
  • Brand New.  Not rebuilt or re-manufactured.
  • No core charge
  • Made In USA
2007-2012 SHELBY GT500 IGNITION COIL SET -- M-12029-4V 2005-2014 MUSTANG PERFORMANCE COOLING FAN -- M-8C607-MSVT
Our Price:$315.00
Sold in Sets of 8
Our Price:$329.00
2007-2012 SHELBY GT500 IGNITION COIL SET -- M-12029-4V 2005-2013 MUSTANG PERFORMANCE COOLING FAN -- M-8C607-MSVT
  • Fits 2007-2012 Shelby GT500 5.4L engines
  • One engine set of (8) OEM Ford Motorcraft stock replacement coils
  • Fits: 2005-2014 Mustang GT  and 2007-2014 Mustang Shelby GT500
  • Original equipment cooling fan on 2013-2014 Mustang Shelby GT500
  • Added cooling capacity for performance applications
   
 
Ford Racing By Speedshop Direct.com
A Subsidiary of
Autocars/Speedshop Direct

3212 El Camino Real Atascadero, CA 93422
 About Us
 Privacy Policy
 Send Us Feedback